| TLSD250/HB2 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LHFP150/EML25 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LAGD125/HFP15 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LGHB2/EML125 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LAGE125/HHT26 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LAHD1000-1 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | Rolling bearing grease life R0F test L50 life at 10 000 r/min., hrs1 000 min. at 100 °– water washout test0–0ThickeneLithium-CalciumEP performance Wear scar DIN 51350/5, 1 400 N, mm1.8 max.Water resistance DIN 51 807/1, 3 hrs at 90 °C1 max.NLGI consistency class1Penetration DIN ISO 2137 60 strokes, |
| LGEV2/0.035 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LGHP2/SD125 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LAGD125/FHF15 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LAGD125/EM2M.LGEM-2 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LAGD125/FG202 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LHSP38/0.015 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |
| LHHT265/EML12 SKF Bearings,Grease and Lubrication,Grease, Lubrications and Oils | ase oil viscosity 40 °C, mm²/s:500; ase oil viscosity 100 °C, mm²/s:32; Penetration DIN ISO 2137 60 strokes, 10–1 mm:265–295; Mechanical stability V2F test:‘M’; Operating temperature range:–20 to +120 °C (–5 to +250 °F); Dropping point DIN ISO 2176:>180 °C (>355 °F); Copper corrosio DIN 51 811:2 max. at 100 °C (210 °F); TLSD series 250 ml refill:LGEM 2/SD250; TLSD series 125 ml refill:LGEM 2/SD125; NLGI consistency class:2; Typical applications:Rolling element bearings running at low speed and very high loads; Jaw crushers; Track laying machines; Lift mast; LAGD series 125 ml:LAGD 125/EM2; TLSD series 125 ml:TLSD 125/EM2; TLSD series 250 ml:TLSD 250/EM2; Features & benefits:High oxidation stability; Molybdenum disulphide and graphite provide lubrication even if the oil film breaks down;; LAGD series 60 ml:LAGD 60/EM2; 420 ml cartridge:LGEM 2/0.4; DIN 51825 code:KPF2K-20; ase oil type:Mineral; 180 kg drum:LGEM 2/180; Shelf life:5 years; Designatio:LGEM 2/(pack size); 18 kg pail:LGEM 2/18; Thickene:Lithium/calcium; Packsize:Designation; 5 kg ca:LGEM 2/5; Colou:Black; Water resistance DIN 51 807/1, 3 hrs at 90 °C:1 max.; Corrosion protectio Emcor: – standard ISO 11007:0–0; Corrosion protectio Emcor: – water washout test:0–0 *; EP performance Wear scar DIN 51350/5, 1 400 N, mm:1,2 max.; Lubrication ability R2F, running test B at 120 °C:Pass at 100 °C (210 °F); Penetration DIN ISO 2137 100 000 strokes, 10–1 mm:325 max.; Oil separatio DIN 51 817, 7 days at 40 °C, static, %:1–5; EP performance 4–ball test, welding load DIN 51350/4, N:3 400 min.; Mechanical stability Roll stability, 50 hrs at 80 °C, 10–1 mm:345 max.; |